ONE word searches yield better results than multiple word searches.

Browse Categories
Browse by Manufacturer
Price Ranges
Search Shopping Lists

Enter the name of your wishlist recipient here to access their wishlist.

<< Previous in End of Train Device Next in End of Train Device >>

Ring Engineering End of Train Device Model # EOT-33-YS Yellow Enclosure 33" wheels Standard Wire Length(Shelf Coupler), HO

FDT Low Price: $39.95
Sale Price: $33.96
You Save: $5.99 (15 %)
This item is currently out of stock.
Item Number: EOT-33-YS
Manufacturer: Ring Engineering

Bookmark and Share
on sale
End of Train Devices with Shelf Couplers #119 Shelf Whisker Coupler
New Page 2
  • HO Scale

  • Ready to Run

  • RailPro, DCC or Analog Compatible

  • Continuous Operation with RailPro and DCC

  • Exceptional Detail including Antenna, Carry Handle, Red Reflector, and More

  • Prototypically Accurate Size

  • Prototypically Accurate Flash Rate and Time create by onboard microcontroller.

  • Low Rolling Friction for an Electrical Pick-Up Design

  • No Batteries Required - Picks up power from the track

  • Fits most train cars

  • #119 Shelf Whisker Coupler Included

  • Black Metal Wheels

  • Prototypically Accurate Exponential Curve in Wheel Face

  • Made in USA


Because the flasher circuit is under the truck, the installation does not affect freight car load!

Without Load Installed With Load Installed

Typical Installations

33" Wheels
Typical Installations

Well Car

Auto Carrier
36" Wheels
Typical Installations

Tank Car

Cement Car
33" Wheels and Long Wires
 Typical Installations

89' Flat

Center Beam

Take a look inside to see the advance electronic and mechanical design that makes the EOT operate without flickering.  The EOT also works well on even moderately dirty and slightly uneven track.

Truck is upside down and cover removed to show electronics. 
Patented Technology - US Patent 7,549,609


Can you really install the End of Train Device in 5 minutes?

 YES.  Because there is no need to drill any holes in your freight car or connect any wires, the installation is simple.  Check the installation instructions on the End of Train Device page.

Does the End of Train Device really work well even though the End of Train Device only uses four wheels for electrical pickup?

 YES.  The End of Train Device has special mechanical and electrical design which allows for flicker free operation even on moderately dirty and slightly uneven track.

Does the End of Train Device require any maintenance?

 YES.  For good operation you will need to clean the End of Train Device's wheels about as often as you clean your locomotive wheels.  The good news is, unlike a locomotive with 8 or 12 wheels, you will only need to clean 4 wheels on the End of Train Device.  Also, you will need to lubricate the bushings once in a while.  Please see instructions for complete details.

Does the End of Train Device work with DCC?

YES.   The End of Train Device works well with DCC (Digital Command Control).  Even when a train comes to a stop the End of Train Device continues to flash at the same brightness, flash rate and on time.

Does the End of Train Device work with an Analog Power Supply?

YES.   The End of Train Device works well with an Analog Power Supply.  When the Power supply gets to about 20% the End of Train Device begins to flash.  Then as the Power is increased to 100% the End of Train Device brightness, flash rate and on time, stay the same because of special on board electronics.  If the Power Supply is less than 20% the End of Train Device stops flashing.  If you have a fairly heavy load for the locomotive to pull, you can often bring up the power supply to the position where the End of Train Device flashes continuously but the train remains still.




Ring Engineering Inc.
228 W. Lincoln Highway #167
Schererville, IN 46375


(219) 322-0279
Mon - Fri 
9am to 5pm Central Time

Product Reviews

(0 Ratings, 0 Reviews)

Mailing Lists
Our best deals & tips in your inbox!
Shopping Cart
Your cart is empty.